More
referral
Increase your income with Hive. Invite your friends and earn real cryptocurrency!

Finminer

What about cryptonight?

Everything is fine with CryptoNight, we support in on AMD and Nvidia

And CPU too? Can it be mined with FinMiner on CPU only?

No, you can use CryptoNight (or Ethash) on GPUs and RandomHash on CPU
By the way, you have wrong ports indicated for PASC on nanopool in your pool list.

Thanks. I’ll check it.
By the way you can contribute to our git too. Pool templates are here, and integrations of FinMiner are here.

Thought I would give FinMiner a try… noticed an increase in stale shares immediately. Opened a ticket on github – https://github.com/FinMiner/FinMiner/issues/28

I switched from Claymore to PhoenixMiner when they came out with a Linux version. PhoenixMiner had the same issue (stale shares) because the miner didn’t recognize/was not tuned for the OpenCL driver version installed…

@nanominer, if you get this fixed, I intend on doing a side-by-side comparison with PhoenixMiner like I did with Claymore…

Hi, @salvo2002 thanks for this results.
I appreciate it very much.
We will check it and try to figure out the reason.

1 Like

What pool are supported by finminer I tried using MPH and it didn’t seem to connect also does finminer support pools with login name instead of eth add

@ATrump

v2.4.6 is out…

https://github.com/FinMiner/FinMiner/releases/download/v2.4.6/FinMiner-linux-2.4.6.tar.gz

Less stale shares on AMD Ethash

Updated in HiveOS 0.6-06@181215.

PhoenixMiner 4.0b vs. FinMiner 2.4.6

Just over 24hrs of testing… PhoenixMiner on top with a margin of 206 more accepted shares.

  • Both running on Hiveon ETH pool
  • Each miner configured with 3 x RX570s 8Gb & 2 x RX580s 8Gb
  • Each miner set to autotune
  • HiveOS autofan control

-------------------/run/hive/miners/phoenixminer/config.txt-------------------
-mport 3335
-rmode 1
-logfile /var/log/miner/phoenixminer/phoenixminer.log
### USER CONFIG ###
-coin ETH
-gpus 12345

-------------------/run/hive/miners/finminer/config.ini-------------------
wallet = 0x
algorithm = ethash
rigPassword = x
pool1 = naw-eth.hiveon.net:4444
pool2 = naw-eth.hiveon.net:14444
pool3 = eu-eth.hiveon.net:4444
pool4 = eu-eth.hiveon.net:14444
mport = -3338
logPath = /var/log/miner/finminer/finminer.log
coin = ETH
rigName = cyrilRX10.finminer
devices = 5,6,7,8,9




1 Like

У меня почему-то нет статистики (см. вложение).


Это можно исправить? или необходимо внести дополнительные настройки?

Настройки нормальные, finminer пока не умеет передавать статистику Паскаля через API, ждём пока пофиксят.

жаль!

Заморочился с парсингом лога. Вывел статистику от туда.

благодарю, так значительно удобнее!

1 Like

Планируется ли добавления майнера:


В следующую сборку Hive?

1 Like

Работаем над этим, но по срокам пока не понятно.
Если хочется напоследок вскопнуть эфир на 1063 можно обратить внимание на claymore 12.0 - он так же экономно расходует память, как и nanominer:

Так и делаю, но Claymore отказывается работать в паре с Finminer по причине нехватки памяти, а этот майнер решил бы эту проблему.

1 Like